Vinyl Flooring Installation in Decatur, GA
Vinyl flooring installation in Decatur is a good fit for rooms that see water and daily wear: kitchens, baths, laundry rooms and finished basements. Sheet vinyl and vinyl tile are soft underfoot, quiet and easy to clean, but they ask a lot of the floor beneath them, so the planning starts with the existing surface rather than the sample board.
This page focuses on sheet vinyl and glue-down or loose-lay vinyl tile. Rigid-core click-lock plank floats instead of bonding, and LVP floors in Decatur have their own page.
Before anything comes up: the age of the old floor
If the house has an older resilient floor, find out what it is before it is torn out. Some older sheet vinyl, vinyl tile and the dark adhesives beneath them contain asbestos, which can be released when the material is broken, sanded or scraped. Sending a small sample to a lab is a minor step compared with cleaning up after a mistake.
If the test is clear, removal proceeds as normal. If it is not, the old floor can sometimes be left in place and covered with new underlayment, or a qualified abatement contractor can remove it first.
Cleaning and smoothing the substrate
Vinyl bonds well to a clean, sound surface and poorly to anything else. Surface contamination such as paint, wax, grease, drywall compound and old adhesive has to be scraped, ground or primed according to the manufacturer’s instructions.
Then comes smoothing. Cracks in a slab, the embossed texture of an old vinyl floor and seams in plywood can all telegraph through new vinyl, so they are filled or leveled with an approved compound. If that raises the floor, we check door clearance before going further.
Moisture and finished height
On concrete, the manufacturer sets a moisture limit and a test method, and glue-down vinyl should not go down until the slab passes. Over wood, we look for signs of past leaks near the toilet, tub, sink and dishwasher, since damaged plywood needs to be replaced first.
Finished height is the other half of this step. We measure the adjacent floors so the transition pieces chosen match the real height difference, taking into account any underlayment the product’s substrate rules require.
Wear surface, pattern and color
The wear surface protects the printed pattern beneath it, and thicker wear layers generally hold up better in kitchens and entries. Pattern and color are best chosen with a large sample on your own floor, under your own lighting, next to cabinets and wall paint.
The adhesive goes on the same list. Each product has approved adhesives for each substrate, and we order the one the instructions specify along with the flooring.
Edges, seams and care afterward
Edge finishing makes the difference between a floor that looks installed and one that looks finished. Cut edges are covered with base or shoe molding, the joint at a tub gets flexible caulk, and toilets are typically reset on a new wax ring after the vinyl runs beneath them. Seams in sheet goods are sealed, and the adhesive coverage is checked before the final walkthrough.
Day-to-day care is light. Grit is what scratches vinyl, so regular sweeping does more than heavy cleaning, and a barely damp mop with the cleaner your product’s maker recommends handles the rest. Skip rubber-backed rugs, which can leave yellow stains on vinyl.
The written estimate should list each room, any testing or removal, substrate preparation, the product and adhesive, trim, transitions and exclusions, along with how changes will be approved.
Decatur’s permit office
Decatur is in DeKalb County. If the project grows to include structural repairs, plumbing or electrical changes, the City of Decatur explains how to obtain a permit through its Design, Environment and Construction Division, and that office can confirm whether your work needs one.
Frequently asked questions
How much height does a new vinyl floor add?
Very little on its own. Sheet vinyl and glue-down tile are only a few millimeters thick. The real height change comes from preparation: new underlayment over a rough subfloor, leveling compound over low spots, or leaving an old floor in place. We measure door clearances and neighboring floors so transitions and any door trimming are planned before installation.
How is the edge of a vinyl floor finished along cabinets?
Along cabinet toe kicks, the vinyl is cut close and the edge is usually covered with a small shoe molding or quarter round, or with a vinyl or rubber toe-kick base. Cabinets normally stay in place, so the new vinyl stops at the cabinet base rather than running underneath. The finishing piece should be agreed and written into the estimate.
Can vinyl flooring go over existing ceramic tile?
Sometimes. If the tile is firmly attached, flat and free of cracks, and the vinyl manufacturer allows it, the grout lines are filled with a skim coat so they do not telegraph, and the vinyl goes on top. This avoids demolition but raises the floor, which can affect doors, appliances and transitions. Loose or cracked tile should come up first.
Talk to us about your Decatur floor
Not sure what is under your current floor, or whether it should come up? Call 404-409-4448. We can look at it in person, measure the room and give you a written estimate that spells out the preparation.