Kitchen Remodeling in Milton, GA

A kitchen is built from dozens of products, and each one comes with a specification sheet listing dimensions, rough-in heights, clearances and power needs. For kitchen remodeling in Milton, we gather those sheets into a single schedule before cabinets are ordered, because the cabinet layout, the wiring and the plumbing all depend on numbers printed on them.

That schedule becomes the reference everyone works from, from the first drawing to the final adjustment.

What goes into a specification schedule

The schedule lists every appliance, sink, faucet, light fixture and hardware piece by brand, model number, finish and quantity. Beside each item go the figures that affect installation: cutout size, required clearances, voltage and circuit size, water and drain connection heights, and any special mounting needs.

Having it all on one page makes gaps obvious. If the range hood is still undecided, nobody can finalize the cabinet above the range or the duct route, and the schedule shows that at a glance.

How appliance specs shape the cabinet layout

Cabinet widths are set by what sits between them. A 36-inch range, a 24-inch dishwasher and a refrigerator with its own width and door swing each claim an exact opening, and the layout fills the remaining wall with boxes and fillers. Built-in models are even stricter, with openings specified to a fraction of an inch.

Clearances matter as much as widths. A wall oven needs a cabinet built to its cutout, a microwave drawer needs a particular base, and a refrigerator beside a wall needs room for its door to open far enough for the bins to slide out.

Rough-in heights for plumbing and power

Faucet and sink specs tell the plumber where the supply lines and drain should come through the wall, and a pot filler over the range has its own mounting height. Electrical specs tell the electrician where each receptacle or junction box belongs: behind the refrigerator, inside the sink base for a disposal, above the hood.

When these locations come from the actual product sheets rather than typical heights, the finished kitchen avoids pipes that collide with drawers and outlets trapped behind appliances.

Lighting from the same schedule

Light fixtures have specifications too. Recessed fixtures list the ceiling depth they need and whether they can touch insulation, under-cabinet fixtures list their mounting depth and where the driver goes, and pendants list hanging height and weight. Placing lights from those sheets lets the electrician set boxes in the right spots while the ceiling is open.

Templating, hardware and the final check

Countertop templating draws on the schedule as well. The fabricator needs the sink model, faucet hole count, cooktop cutout and any accessory holes before cutting. Once the counters are in, appliance clearances, faucet reach and hardware placement are compared with the schedule before the final review.

Hardware deserves the same care. Choose pulls by their center-to-center hole spacing as well as their look, since changing them later means drilling or filling holes in finished doors. Other rooms in the house are covered on our page for remodeling in Milton.

Permit cards and inspections in Milton

The city’s Community Development Department issues permits for all construction activity through its CityView web portal, and inspections are booked through the portal or by email. Under the city code (§ 10-86), plumbing work needs a permit, an owner can obtain one only as a license-holding contractor or as the resident of the home being altered, and minor repairs valued under 1,000 dollars may go ahead without a permit only if the building official approves.

A related section (§ 10-93) says work may not begin until the permit card is posted at the site. It also calls for an underground plumbing inspection once trenches are dug and pipe is installed but before backfill, which can come into play when a new sink location needs piping beneath a slab floor.

Questions about spec sheets, permit cards and pot fillers in Milton

What is a product specification sheet?

It is the manufacturer’s document listing a product’s exact dimensions, required clearances, cutout sizes, electrical needs and plumbing connection points. Appliances, sinks, faucets, hoods and light fixtures all have one. Cabinet openings, rough-in heights and countertop cutouts are set from these sheets, so collecting them before ordering prevents parts that do not fit.

Does work have to wait until the permit card is posted in Milton?

Yes. The city code says work cannot start until the permit card is posted on site. Permits are issued through the CityView portal, and plumbing work requires one; an owner qualifies only as a license-holding contractor or as the occupant of the home. Inspections, including an underground plumbing inspection before backfill where it applies, are scheduled through the portal or by email.

What is a pot filler, and what does it need?

A pot filler is a wall-mounted faucet with a folding arm above the range, used to fill large pots right where they will be cooked. It needs a cold-water line run inside the wall to a set height, chosen from the faucet’s specification and the height of your tallest pot. Plan it before the wall is closed and the backsplash goes up.

Start your specification list

If you are gathering appliances and fixtures for a new kitchen, call 404-409-4448. We can review the products you are considering, measure the room and build a written estimate around their specifications.