Hardwood Floor Refinishing & Sanding in Dunwoody, GA
Before talking about colors, it helps to know what kind of floor you have. Hardwood floor refinishing in Dunwoody can mean sanding a site-finished oak floor that has been refinished before, or tackling a prefinished floor with a tough factory coating and beveled edges. The type of floor, its existing finish and how far wear has reached into the wood shape every step that follows.
Site-finished or prefinished?
Site-finished floors were sanded and coated in place after installation. Their boards meet with tight, square edges, and the finish forms a continuous film across the joints. They are usually straightforward to refinish.
Prefinished floors arrive from the factory already coated, often with small bevels along the board edges. That factory coating is very hard, so sanding it off takes more effort and abrasive, and the bevels may remain as shallow grooves unless the floor is cut deeper than is sensible. Some owners keep the bevels as part of the look; others prefer a recoat with a product designed to bond to factory finishes.
Existing finish, wear depth and board damage in Dunwoody
On either type, the next question is how deep the wear goes. Scuffs in the finish may only need a recoat. Gray lanes, deep scratches and dents mean a full sand. Board damage such as splits, burns or deep pet stains usually means replacement, especially if the floor has limited thickness left. Lifting a floor register shows the board profile and helps confirm how much wood remains above the tongue.
Loose boards and chipped edges at vents and doorways go on the repair list now, before any sanding.
Choosing sheen and deciding on natural or stained
Sheen is simple to change during a refinish and awkward to change afterward. Matte looks close to bare wood and hides scratches well; satin is a step up with a soft glow; semi-gloss and gloss reflect more light and show wear sooner.
Natural versus stained depends partly on remaining thickness. Going from a dark existing color back to natural can require extra sanding, so on a thin floor a mid or darker tone may be the more practical choice.
Transitions, cabinets and the repair scope
Decide how thresholds, reducers and stair nosings will be treated, and settle the repair scope at the same time. The floor along fixed cabinets is finished up to the toe kick, with that line hand-scraped and detailed. If new boards must be added to a room, see our hardwood floor installation in Dunwoody page.
Order of work, from repairs to the last coat
The sequence runs from containment and dust protection to board repairs, sanding through the grits, edging and hand scraping, vacuuming, stain samples and stain if chosen, and finally the finish coats. Check stain expectations on samples that include repaired areas, because new boards can take color differently. Dust control continues throughout, with sealed doorways, covered returns and the HVAC off.
The finish must cure before the rooms return to normal use, and the manufacturer’s data sheet gives those times. The final review checks sheen consistency and edge work and takes a second look at any boards replaced for pet damage or deep stains.
Permit questions and a clear estimate
Dunwoody is in DeKalb County. If subfloor or joist repairs turn up, or the project grows to include plumbing or electrical changes, contact the City of Dunwoody Permits & Inspections office in Community Development to find out whether a permit is needed.
The written estimate should state the floor type, recoat or full sand, rooms and area, the boards to be replaced or a price per board, natural or stained, the sheen and finish product, the number of coats, threshold and cabinet edge work, furniture moving and cleanup, and how changes found during sanding will be priced and approved.
Questions about refinishing floors in Dunwoody
Can prefinished hardwood floors be sanded and refinished?
Usually, if the boards are solid or have a thick enough veneer. The factory finish is very hard, so removing it takes more sanding than a site-finished floor, and beveled edges may remain as small grooves. If the floor is in fair shape, a recoat with a product made to bond to factory finishes may be an alternative to test first.
How do I know whether my Dunwoody floor is site-finished or prefinished?
Look at the board edges. Prefinished floors often have small bevels where boards meet, and the finish does not bridge across the joints. Site-finished floors usually have square edges with a continuous film of finish across the seams. A refinisher can confirm, and may check a hidden spot such as inside a closet or at a floor register.
Why does the sheen level matter when refinishing?
Sheen controls how much light the floor reflects, which changes both the look and how quickly wear shows. Matte and satin hide scratches, dust and minor flaws; semi-gloss and gloss highlight them. Because sheen is set by the final coat, changing it later means another recoat, so choose it carefully with a sample before the job starts.
Talk with us about your Dunwoody floors
Not sure whether your floor is site-finished or prefinished? That is fine. Call 404-409-4448, say whether it has been refinished before, and we can check the floor type and condition in person before putting together a written estimate.