Carpet Installation in Alpharetta, GA

Carpet usually goes down last, after paint and trim, and it has to meet everything else in the house: door bottoms, hard floors in the hallway, the edges of stair treads. For carpet installation in Alpharetta, we start with those meeting points, because a pad choice or doorway detail that was not planned shows up every time someone closes a door or steps from tile onto carpet.

How pad choice changes the height at every doorway

The cushion under carpet does more than add softness. It absorbs foot traffic so the backing does not grind against the subfloor, and it adds height. A thick pad under a thick cut pile can raise the floor enough that a bedroom door which cleared the old carpet now catches.

Common options include rebond, made from recycled foam pieces pressed together, prime and frothed foams, fiber pads and rubber. Carpet makers generally list an allowable thickness range and a minimum density, and loop styles such as Berber usually call for a thinner, firmer cushion. We match the pad to those requirements rather than to how soft it feels in a showroom.

Door clearance and the doors that need trimming

During the visit we open and close each door over the area being carpeted and look at the gap beneath it. Once the combined thickness of carpet and pad is known, we can tell you which doors are likely to rub. Those are taken off their hinges, cut at the bottom and rehung, and the estimate should say whether that work is included.

Bifold and sliding closet doors often need their floor guides reset after the carpet goes in. A door that lets air reach a return vent also needs a gap left under it so air can still move when it is closed.

Measuring rooms and planning where seams fall

Room dimensions drive the seam plan. Carpet comes off rolls of a fixed width, so we measure each space, including closets and hall offsets, and decide how pieces will be cut to keep seams away from doorways and busy paths. While measuring we also check the stair nosings and feel for subfloor panels that give underfoot, since both add preparation time.

The layout sheet should show seam locations and pile direction for every room. Ask to see it; it explains why the yardage ordered is more than the square footage of the floor.

Where carpet meets hard flooring

Transitions are the visible edge of the job. Between carpet and tile, hardwood or vinyl plank, the usual choices are a hidden metal edge, often called a Z-bar, that grips the carpet and tucks it against the hard floor, or a visible metal or wood strip that covers the joint. Which one fits depends on the height difference between the two surfaces.

When the hard floor is new too, planning both together keeps the heights in line. If you are deciding which rooms get carpet and which get plank, our page on LVP flooring installation in Alpharetta explains how that floor is installed and finished at doorways.

Fiber, pile style and weight for each room

Nylon is resilient and handles halls and stairs well. Polyester and triexta feel soft and resist many water-based stains, though polyester can flatten sooner under heavy traffic. Wool is a natural, higher-cost fiber, and olefin is common in loop styles. Pile style matters as much: cut pile feels soft, loop pile hides footprints, and frieze or textured cut pile hides vacuum marks.

Weight completes the picture. Compare face weight alongside density so you are not paying for tall yarn that will lie down in a year.

Order of work, ending with transitions and stairs

Rooms are cleared, the subfloor is prepared and tack strip is checked or replaced. Pad goes in, carpet is laid out and seamed, then power-stretched so it stays flat. Transitions are fastened at each hard-floor edge, and stairs usually come last, wrapped waterfall style or tailored around each nosing. If treads or nosings need repair first, see our staircase remodeling page for Alpharetta.

Before the job is called finished, we look over seam lines, pile direction where rooms meet, transition height and every door swing.

Permits for work beyond the carpet in Alpharetta

Alpharetta is in Fulton County. If the project grows to include repairing floor framing, moving a floor outlet or changing plumbing, put that to the City of Alpharetta Community Development, Construction and Inspections office, which can say whether that part of the work needs a permit.

Common pad, door and transition questions

Is a thicker carpet pad better?

Not always. A pad that is too thick or too soft lets the carpet backing flex with each step, which can loosen the stretch, strain seams and cause ripples. Most carpet makers list a thickness range and minimum density for their products, and loop carpets usually need a thinner, firmer cushion. Stay within those limits, then choose for comfort.

Will my interior doors need trimming after new carpet goes in?

Some may. It depends on how much height the new carpet and pad add compared with the old floor, and how much gap each door has now. We check every door during the visit, and doors that would rub are removed, cut at the bottom and rehung. The estimate should state whether door trimming is included.

What goes between carpet and a tile or plank floor at a doorway?

Most often a concealed metal gripper that holds the carpet edge snug against the hard surface, or an exposed strip laid over the joint. Which is better comes down to how far apart the two floor heights are and the look you prefer. The joint is normally placed so it sits under the door when the door is closed.

Arrange a carpet visit in Alpharetta

To talk through rooms, stairs and transitions, call 404-409-4448. We can schedule a time to measure, check doors and subfloor, and put a written estimate together.