Vinyl Flooring Installation in Lilburn, GA
A new vinyl floor is often one part of a bigger update: fresh paint, a vanity swap, new baseboards, maybe new kitchen cabinets. When vinyl flooring installation in Lilburn is part of a project like that, the order of the trades matters as much as the floor itself. In the wrong sequence, the painter drips on the new surface, the toilet gets set twice, or the dishwasher no longer slides out.
Here we cover sheet vinyl and vinyl tile, glued or loose-laid, and how that work fits into the rest of a remodel. Rigid-core click-lock plank is handled on our LVP flooring page for Lilburn.
Paint before or after the floor?
Most painting goes first. Ceilings and walls can be rolled with drop cloths over the old floor, which is about to come out anyway, so a splatter costs nothing. The exception is trim: if new baseboard or shoe molding goes on after the vinyl, it gets its final coat afterward, with tape protecting the new floor. Expect a little touch-up along the bottom of the wall once the trim is nailed.
Cabinets, vanities and the floor
Whether new cabinets go in before or after the floor depends on the product. Some vinyl manufacturers allow cabinets on top of glue-down material; others want the floor to stop at the cabinet base. Running vinyl under the boxes uses more material but keeps the floor continuous if the layout changes later. Setting cabinets first saves material and keeps the new surface away from cabinet installation. We read the product’s instructions and decide with you before ordering.
Vanities follow the same logic. A freestanding vanity usually comes out so the vinyl can run beneath it, then returns on top.
Toilets, appliances and finished height
The toilet is pulled before installation, and the vinyl runs under it to the flange. Resetting it on a new wax ring is part of the job. In the kitchen, the dishwasher opening is measured before and after preparation, because leveling compound or a new underlayment panel can raise the floor enough to trap the dishwasher beneath the countertop. The refrigerator alcove and range space are checked the same way.
Checking the substrate against the product’s requirements
Before anything is ordered, we compare the existing floor with the manufacturer’s substrate requirements: which subfloors are accepted, how flat and smooth the surface must be, which patching compounds are approved and what moisture limits apply to concrete. A room that fails one of those checks needs work first, and that work belongs in the schedule ahead of the floor rather than being discovered on installation day.
Moisture is a common example. A slab that tests above the product’s limit may need a mitigation step or a different adhesive, which adds time between demolition and the new floor.
Base or shoe molding at the edges
There are two usual ways to finish the edge. Leaving the baseboards in place and adding a small shoe molding over the vinyl’s edge is quick and avoids wall repairs. Taking the baseboards off and reinstalling them, or fitting new ones after the floor, gives a cleaner line without shoe molding, but it means caulking and paint touch-up. Your choice changes the order of work, so we settle it at the planning stage.
Transitions to rooms you are not redoing
Rooms left alone in this round still meet the new floor. Vinyl usually sits lower than hardwood, tile or carpet, so each doorway gets a reducer, a carpet edge or a T-molding sized to the measured difference. If a later phase will replace the neighboring floor, a transition that is easy to swap out makes sense. Homeowners who plan to do the adjoining rooms later sometimes look at laminate flooring installation in Lilburn for those spaces.
A note for Lilburn projects that grow
Lilburn is in Gwinnett County. When a remodel adds structural, plumbing or electrical work to the new floor, look at the City of Lilburn’s building and trade permits page to see whether that part of the job needs a permit.
Remodel sequencing questions
Should I paint the walls before or after the vinyl floor goes in?
Paint walls and ceilings before the new floor whenever you can. The old flooring is coming out, so drips on it do not matter, and the painter can work without worrying about the new surface. Trim is the exception: new baseboard or shoe molding installed after the vinyl gets its final coat afterward, with the floor taped and covered while that happens.
Can the toilet go back on right after the vinyl is installed?
Often it can, but it depends on the adhesive. Some adhesives need time before they carry a concentrated load, and the installation instructions say how long. The toilet is reset on a new wax ring, and the flange height is checked against the new floor. If the floor ends up higher, a flange extension or a thicker seal may be needed for a tight connection.
Do I need new baseboards when I replace a vinyl floor?
Not necessarily. Existing baseboards can stay, with a shoe molding added to cover the edge of the new vinyl. New or reinstalled baseboards are worth considering if the old ones are damaged, if you dislike the look of shoe molding, or if the walls are being repainted anyway. Removing baseboards can mark the wall, so plan for some caulk and paint.
Bring us your remodel plan
Call 404-409-4448 and walk us through the whole project, not just the floor, so the vinyl can be scheduled in the right place among the other trades. We can visit to measure, check the substrate and prepare a written estimate.