Bathroom Remodeling in Campbellton, GA

A good bathroom remodeling plan in Campbellton starts with a tape measure rather than a catalog. The width of the room, the swing of the door and the position of the existing drains decide how large the vanity can be, whether the shower can grow and where tile has to stop. Once those limits are on paper, choosing finishes gets much easier.

Precision Remodeling measures the room, records what is behind the walls and floor where it can be seen, and then writes a scope you can read line by line. Here is what that involves.

Sizing the vanity to the room

Vanity sizing is a balance. A wider cabinet gives more counter and drawer space, but it can crowd the toilet or narrow the path to the shower. Depth matters as well; a standard-depth cabinet may stick out too far in a narrow bath, while a shallower unit leaves more floor space at the cost of some storage.

We draw the vanity, toilet and shower together with their clearances, then show how the mirror, lights and outlets line up with the cabinet you choose. The shower size and the storage pieces go on the same drawing, so every trade works from one plan.

Tile transitions at the door, tub and shower

Every place where tile ends needs a decision. At the doorway, the new floor may be taller than the hallway flooring, which calls for a beveled threshold or metal transition strip. Where wall tile meets a tub, the joint is sealed with a flexible caulk rather than grout, because the tub moves slightly when it fills with water.

The tile and grout you choose affect these edges as well. Rectified porcelain allows narrow grout joints, while handmade or tumbled tile needs wider ones. Cement-based grout should be sealed, and epoxy grout resists staining but takes more skill to install. Patterns, tile sizes and setting materials are explained on our Campbellton tile installation page.

Looking at drains, supplies and the floor

The location of the drain and supply lines often decides what a new layout costs. Keeping the toilet, sink and shower in roughly their current spots usually keeps the plumbing cost down. Moving them can still make sense, but it means new pipe runs with proper slope and venting, and we check whether the lines are reachable from below or buried in a slab.

The subfloor and the doorway threshold are looked at together. If the subfloor is uneven or soft, it needs repair or an added layer before tile, and that added thickness affects the threshold at the door. Each repair the floor needs is listed in the estimate.

Shower glass, lighting and hardware

For the shower enclosure, the main configurations are a single fixed panel, a hinged door with an adjoining panel, and a sliding door. Each has trade-offs: a fixed panel has no moving parts but lets some spray escape at the opening, while a hinged door needs room to swing outward. The glass is measured after tile so it fits the finished walls.

Lighting choices include the vanity fixture or side sconces, a recessed light over the shower rated for wet locations, and sometimes a dimmable ceiling light. Hardware, from the door lever to the towel ring, looks most cohesive when it is ordered in one finish alongside the faucet and shower trim.

Sequence, final checks and the written scope

Work generally runs in this order:

1. Protect the floors and the paths that lead to the bathroom.
2. Take out the fixtures and finishes being replaced.
3. Complete approved plumbing, electrical and framing changes.
4. Install backer and waterproofing, then tile.
5. Set the vanity, top, toilet and fixtures, then hang the glass.
6. Add lighting trim, storage pieces and accessories.

At the end, the shower layout and ventilation get a final check: the fan runs and vents outside, the glass closes cleanly and the valve and showerhead sit where the drawing placed them. Before scheduling, the measured scope and every finish decision that affects installation should be confirmed in writing, so the plan reflects your bathroom rather than generic allowances.

Which city handles your permit

Historic Campbellton lies in southwest Fulton County, partly in the City of South Fulton and partly in the City of Chattahoochee Hills, as described on South Fulton’s Historic Campbellton Crossroads page. Because the area is split, the permitting office depends on which city your address falls in. If your project includes plumbing, electrical or structural changes, check with that city’s office whether a permit is needed before work starts.

Frequently asked questions

How do I know what size vanity will fit my bathroom?

Measure the wall, then subtract the space the toilet and door need. The toilet needs clear room at its side, and the door and any drawers must open without hitting each other. Depth matters too, especially in narrow rooms. We draw the options to scale so you can compare a wider cabinet against a roomier walkway before ordering.

Which permit office covers a Campbellton address?

Historic Campbellton is split between the City of South Fulton and the City of Chattahoochee Hills, both in southwest Fulton County. The office that handles permits depends on which of the two cities your address is in. If you are unsure, your property records or the cities themselves can confirm it before plumbing or electrical work is planned.

Why does the threshold height change after a remodel?

A tile floor is built in layers: the subfloor, sometimes an added underlayment or membrane, the thin-set mortar and the tile itself. Together they are often thicker than the vinyl or older tile being removed. The hallway floor stays the same, so a transition piece is needed to bridge the difference smoothly and avoid a tripping edge.

Start with a tape measure

To talk about your bathroom, call 404-409-4448. Tell us roughly where the house is and what feels too tight in the current room, and we can arrange a visit to measure and prepare a written estimate.