Carpet Installation in Tucker, GA

Most of a carpet’s edge disappears against the wall, and when it is done well nobody notices it. When it is done poorly, you see gaps under the baseboard, frayed yarn along the wall or a lumpy line where carpet meets quarter round. Carpet installation in Tucker includes planning those edges: baseboard height, trim, paint timing and the spots where carpet meets a hearth, a built-in or a hard floor.

How carpet finishes at the wall

Tack strip is nailed around the room with a small gap between the strip and the wall. When the carpet is stretched onto the strip’s pins, the installer trims it slightly long and tucks the edge down into that gap with a stair tool, so the cut edge hides at the base of the wall. The gap has to suit the carpet’s thickness: too wide and the edge can pull out, too narrow and it bulges.

Baseboards, quarter round and shoe molding

Hard floors often have quarter round or shoe molding along the baseboard to cover the expansion gap. Carpet does not need it. Left in place, it creates a ledge the carpet butts against instead of tucking under, and the edge looks uneven. When a hard floor is being replaced with carpet, the shoe molding usually comes off and the nail holes in the baseboard are filled and touched up.

If new baseboards are part of the project, install them before the carpet and set them slightly above the subfloor so there is room for the carpet to tuck beneath. Putting baseboards in after the carpet makes a clean tuck harder to achieve.

Painting trim before or after

Paint baseboards and walls before the carpet goes in, while drips can land on the old floor or on drop cloths. The installation itself, tucking and trimming close to the wall, can leave the odd scuff on fresh paint, so plan a light touch-up afterward and keep a little of the trim paint. If carpet has to go in first for scheduling reasons, painters will need to tape and cover the carpet edge carefully.

Room dimensions and seams near walls

Walls are rarely perfectly straight or square. We measure every wall and note jogs, bump-outs and closets, then plan seams from those dimensions and the roll width. A layout should not leave a thin sliver of carpet along a wall, because a narrow strip is hard to stretch and tends to work loose, so the plan is adjusted until edge pieces are wide enough to hold. Pile direction stays the same in every piece so the carpet looks even right up to the baseboard.

Hearths, built-ins and other edges

Not every carpet edge meets a baseboard. At a fireplace hearth, the carpet usually tucks tightly against the stone or tile. At built-in cabinets or a raised platform, it may tuck under a toe-kick or finish with a metal edge. Low wall vents and outlets near the floor are worked around neatly. Each of these is noted at the visit so it is planned in advance rather than improvised.

Transition hardware, furniture and the subfloor

At doorways to tile, wood or vinyl, the carpet edge gets hardware suited to both floor heights: a metal gripper edge, a reducer or a tuck against a hard-floor nosing. If a neighboring room is going to plank, our LVP flooring installation in Tucker can be scheduled so the transitions are set once. Before any of this, furniture is moved out, the old floor removed and the subfloor checked; loose panels are fastened and damaged sections replaced so both the edges and the field lie flat.

Tucker permits

Tucker lies in DeKalb County. Carpet and trim are finish work, but if the project also covers wall changes, electrical work or plumbing, ask the City of Tucker’s Building and Permitting Division whether that part needs a permit.

Edge and trim questions

Should the quarter round come off before carpet is installed?

Usually, yes. Quarter round and shoe molding cover the expansion gap along a hard floor, but carpet tucks under the baseboard and does not need them. If the molding stays, the carpet butts against it and leaves an uneven edge. Removing it, then filling and touching up the nail holes in the baseboard, gives a cleaner finish, and the molding can be saved in case you return to a hard floor later.

Will installing carpet scuff freshly painted baseboards?

It can leave minor marks. Installers work close to the wall while trimming and tucking the carpet, and tools or the carpet edge may rub the paint. Most scuffs are small, and a few minutes with a brush and the leftover trim paint takes care of them. Painting before the carpet goes in is still the right order, since it keeps paint off the new carpet.

Why is there a gap between the baseboard and the subfloor?

It leaves room for the carpet edge. When carpet is installed, the cut edge is tucked down between the tack strip and the wall, and a small space under the baseboard lets it slide in neatly. Baseboards set tight to the subfloor still work, but the tuck is harder. With hard floors, the same space hides the expansion gap the flooring needs.

Get the details right in your Tucker home

Call 404-409-4448 to tell us about the rooms, the trim and any baseboard or painting plans. We can arrange a visit to measure and go over the edges with you, then send a written estimate.