Bathroom Remodeling in Kellogg, GA

A bathroom gets more water, steam and daily wear than any other room in the house, so the way it is built matters as much as how it looks. When Precision Remodeling takes on a bathroom remodel in Kellogg, waterproofing and the spacing between fixtures come first, followed by glass, lighting, tile and the floor beneath it.

Waterproofing the shower properly

Tile looks solid, but grout lets moisture pass, and over time water reaches whatever is behind it. A shower therefore needs a continuous waterproof layer under the tile. That can be a sheet membrane, a liquid membrane rolled onto backer board, or a liner below a mortar bed. Whichever system is used, it has to be unbroken at inside corners, the curb, the niche and every pipe opening.

The shower floor is built with an even slope to the drain so water never collects. A flood test, done before tile, confirms that the base holds water.

Spacing fixtures and locating the plumbing

Fixture spacing is about daily comfort. There should be comfortable space beside and in front of the toilet, room for the vanity drawers to open and a clear arc for the shower door. We draw the room to scale so you can see the clearances before deciding on fixture sizes.

The drain and supply locations are mapped at the same time. Fixtures that stay in place reuse existing lines, while relocated fixtures need new pipe runs with slope and venting. How easily a drain can move depends on whether there is a crawlspace, basement or slab below.

Shower glass, lighting and hardware choices

The shower glass configuration depends on the opening. A fixed panel works for longer showers, a hinged door with a side panel fits most standard openings, and a sliding door suits tight rooms where a swinging door would hit the toilet. Glass is measured after tile so it fits the finished walls.

Lighting is planned in layers: fixtures at the mirror for grooming, a ceiling light for the room and a wet-rated light over the shower if needed. Hardware, such as towel bars, hooks and grab bars, is chosen early so blocking can be installed behind it.

Tile, grout and the subfloor beneath them

Tile is chosen for the surface it covers. Porcelain resists water and wear, natural stone needs sealing, and small mosaics provide grip on shower floors. Grout can be cement-based and sealed, or a more stain-resistant type. Layout and material choices are discussed further on the Kellogg tile installation page.

Underneath, the subfloor and the threshold are planned as a pair. The subfloor must be stiff and flat, so soft or damaged areas are repaired first. Any added layers raise the finished floor, and the doorway threshold is planned to meet the next room smoothly.

Who does what: deliveries, debris and cleanup

The written scope should say who moves the contents out of the bathroom, who receives material deliveries and where they are stored, how demolition debris and packaging are hauled away, and who handles final cleanup. Agreeing on these points in writing prevents confusion once work begins. If the project changes plumbing or wiring, ask the local building office whether a permit is needed before work starts.

Phasing, sequence and final checks

If you prefer to remodel in stages, start with what will be buried: new piping, the waterproofing, the exhaust duct and any floor repair. Mirrors, light fixtures and accessories can be updated later. Keep a record of the fixture models, the grout color and the paint, so later purchases match what is already installed.

For a single project, the order is protection, removal, rough changes to plumbing, electrical and the fan, waterproofing, tile, then fixtures, glass and trim. The shower layout and the ventilation route are settled during rough-in. As the job wraps up, the lights, medicine cabinet and niche are compared with the drawing, and painted walls get a finish suited to humidity; our interior painting page for Kellogg explains the options.

Frequently asked questions

What is the most important part of a shower remodel?

The waterproofing. Tile and grout are the visible finish, but the membrane or liner behind them keeps water out of the walls and floor. A shower with attractive tile and a gap in its waterproofing can leak into the framing for years before anyone notices. Testing the shower base before tile covers it is a simple safeguard.

Can bathroom fixtures be moved to new locations?

Usually, yes. Moving a toilet, sink or shower means new drain and supply lines, and drains need a steady slope and a vent. The work is simpler over a crawlspace or basement than on a concrete slab, where the floor must be cut. The existing plumbing is mapped before a new layout is priced.

What should I decide first when planning a bathroom?

Start with the layout: where the shower, toilet and vanity go, and how much space each needs. Those decisions set the plumbing work and the vanity size. Next come the shower details, such as valve location, niche and glass type, followed by tile, lighting and hardware selections.

Describe your project

Call 404-409-4448 to tell us about the bathroom you want to change in Kellogg. We can arrange a visit to measure and review the room, and then provide a written estimate.